And for the first port, it will utilize the mSATA card adapted with the mini-SAS connector. ![]() As for the EC slot, I found the edge connector to build an EC to SATA adapter card. Two SATA ports will connect to those mSATA adapters with the tx/rx corrected. I currently have half the connectors designed in Eagle. I also decided I may add a SATA power connector in case I wanted to try out non-powered cards. And locking the GPU down with a latch seems unnecessary as it fits extremely snug. I decided to do a mock up of the setup to see if there's any location issues sure enough because of the cabling it requires more space for the powerful dual slot cards that would complement the 3720QM. Recognize that funny looking connector next to the three SATA ports? It's a mini-SAS port that conveniently has enough pins for port 1 and utilizes differential pairs. It's good to see this thread is live and well tackling that Emodule slot. I closed my laptop and I am heading to bed since I am working tomorrow, but I am going to try it in the next days. Maybe pulling this pin low could trigger something? MOD_SATA_PCIE#_DET on the other side goes on a ECE5048-LZY_DQFN132 controller (pg 39 UMA) which seems to handle a lot of things. On the schematics it goes on controller MEC5055-LZY. ![]() I took apart an 12,7mm ODD caddy I had laying around just to find out that pin 4 is not connected while pin 1 DEVICE DET# is pulled low? I think. Even when I taped this pin my dvd would work. I checked on other schematics and the "official" SATA pinout and I found out that this particular pin (pin 4) is a manufacturing diagnostic pin. There is the MD signal on the SATA power connector. This adapter goes into the modular bay and every TX-RX signal goes on my riser.Īccording to our JSATA2 schematics (below) and as you noticed Used an old mini pcie adapter that I cut so it would fit. So I built an adapter to connect into the Module Bay slot. If I didn't wreck the ODD port, I would have gotten USB3.0 module, it's probably PCI like you say and will provide the correct connector.įinally got my PE3A to work. And those lanes are direct to CPU, can those be disabled by PCH for example? So maybe we need to enable USB3.0 mode with those mod pins (MOD_MD, MOD_SATA_PCIE#_DET), and I tried one of them. We could probably get a photo from someone who has already purchased it? I couldn't find any closeup to the connector online either. (I could upload a photo if you are interested). I own one EC to USB 3.0 adapter which uses the ASM chip and the tracks from the chip go to the PCIe signals on the EC slot. I got to that conclusion cause there are plenty EC to USB 3.0 adapters (found on eBay) using the USB 3.0 NEC/Renesas Chip or the USB 3.0 ASM1042. I assumed that the Modular Bay uses some kind of PCIe->USB 3.0 card.There is no schematic that I could find for the USB3.0 Expansion module. ![]() I have been trying unsuccessfully to fix my PE3A to check myself but I failed. When I made the x2 2.0 connection with port 1 WWAN and port 2 WLAN I only used TX/RX signals & GND from port 2. You can check if your so-dimms have XMP Profiles using Thaiphoon Burner DEMO. You can do the same on your sticks if they do not have XMP Profiles already. ![]() I flashed XMP Profiles on my stock memories described here. Using as a guide Atonus instructions I changed my DIMM profile (in my bios 0x1ee) from default (value 0x0) to XMP Profile 1 (value 0x2) and XMP Profile 2. In this file, you can find UEFI variables for changes you may want to make, although they are invisible in the system's UEFI BIOS.įor example on my Dell E6430 there was no option in my BIOS to enable XMP Profile. Since this is for the A17 bios, is that best since its the latest one doing 1866? Again im not sure how to implement this. donovan6000's Blog: Universal IFR ExtractorĪlso the link to the UEFITool 0.18.8l tool is broken. I just have one question, how do I actually implement this? Im not sure how you even extracted this because the site for the donovan universal extractor is doing maintenance for however long.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |